Aluminum
Powder-coated aluminum is light, resists rust and works well for most residential entrances. It is available in modern and ornamental styles.
- Upkeep
- Wash and inspect yearly
- Panel cost, 12 ft
- $1,400 to $3,200
Driveway gates
Driveway gate installation and repair in Seneca, SC
We build and install custom swing, slide and cantilever driveway gates in aluminum, steel and wood. We also install and repair operators, keypads, app controls and solar power from many major brands.
Gate stuck closed with a car inside?Keep clear of the gate and do not force it open. Call us and tell us access is blocked so we can prioritize the visit.
- Freesite visit for new installations
- 5 yrswarranty on new gate systems
- Many brandsof gate operators serviced
- 2 to 3 weekstypical installation timeline
Gate fit finder
Which gate fits your driveway
Driveway slope, opening width and room beside the entrance help determine which gate will work best.
Likely fit
Dual swing gate
A good fit for a flat opening from 12 to 16 ft with room for two panels to swing inward.
Automated, installed$5,400 to $8,900Confirm with a site visitSwing, slide and cantilever
Types of driveway gates we install
The right system depends on the driveway slope, surface and available room. We confirm the fit during the site visit.
| Compare | Swing gateOne or two panels on hinges, arcing inward like a door. Most common on residential drives. | Track slide gateOne panel rolls sideways on a ground track beside the driveway. | CantileverSlides on rollers mounted to posts. Nothing touches the ground, so gravel and leaves cannot jam it. |
|---|---|---|---|
| Best when | The driveway is flat at the gate and there is 12 to 16 ft of room inside for panels to open. | Sloped or tight inside the gate, paved drive, fence line to slide along. | Same as slide, but on gravel, in leaves, or where frost and debris would foul a track. |
| Ground work | Two posts or columns. No concrete in the drive. | Posts plus a level concrete strip with steel V-track set across the opening. | Three posts on one side on a shared footing. Nothing in the drive. |
| Space needed | An arc equal to gate width behind each leaf. | Fence run equal to the opening beside the drive. | Fence run 1.5 times the opening, for the counterbalance tail. |
| Operator | An arm operator on each gate panel. | A chain-drive operator beside the opening. | A chain-drive operator beside the opening. |
| Upkeep | Lubricate hinges and check alignment. | Keep the track clear and inspect the rollers. | Lubricate rollers and check alignment. |
| Automated, installed | $4,800–$8,900 | $6,500–$10,500 | $7,200–$12,500 |
Prices are typical ranges for a complete automated gate. The site visit confirms the gate type, power requirements and final price.
Gate materials
Driveway gate materials
Gate panels are built to fit the opening and are available in simple farm, modern and ornamental styles.
Steel and wrought iron
Steel provides a heavier look and works well with stone columns. The finish needs regular inspection so chips can be repaired before rust develops.
- Panel cost, 12 ft
- $2,200 to $5,500
Wood on an aluminum frame
Wood boards over a welded aluminum frame provide privacy and a warmer appearance. The wood needs periodic cleaning and sealing.
- Panel cost, 12 ft
- $2,600 to $6,000
Tube-steel farm gate
An existing farm gate can often be automated if the gate moves freely and the posts are solid.
- Automate existing
- From $1,850
Operators, power and access
Gate operators and access controls
We match the operator, power source and access controls to the gate size and the way the entrance is used.
Standard on every install
A properly sized operator, battery backup, two remotes, required safety sensors and an inside exit device.
Swing operators
Arm operators open one or two hinged panels. We size the equipment to the panel length, weight and expected daily use.
Slide operators
Chain-drive operators move track and cantilever gates. They mount beside the opening on a concrete pad.
Solar or hard-wired power
Hard-wired power is best when electricity is close to the entrance. Solar can be practical on long driveways with a clear location for the panel.
Keypads and remotes
Keypads provide separate entry codes for family, guests and service providers. Remotes and compatible vehicle controls can also be programmed.
Phone app and video intercom
App controls let you open the gate remotely. A video intercom lets visitors call before you grant access.
Safety sensors
Photo eyes and monitored edge sensors stop or reverse the gate when an obstruction is detected. We inspect the safety devices during every repair.
Driveway gate pricing
Automatic driveway gate pricing
These typical ranges include the gate equipment, installation and basic access controls. We provide the final price after the site visit.
Package 1
Automate the gate you have
For an existing gate that moves freely and has solid posts. Includes the operator, safety sensors and basic access controls.
- Swing or slide gate
- Solar or wired power
- Site condition confirmed first
$1,850 to $3,400typically 1 day
Package 2, most homes
New automated aluminum swing gate
Includes new posts, powder-coated aluminum panels, operators, safety sensors and basic access controls.
- Single or dual swing
- Several panel styles
- Column mounting available
$4,800 to $8,900typically 2 days on site
Package 3
New automated slide or cantilever gate
For sloped, tight or wide entrances. Includes the gate, posts, operator, safety sensors and basic access controls.
- Track gate on pavement
- Cantilever for gravel
- Wide-opening options
$6,500 to $12,500typically 2 to 3 days
Extra trenching, pavement cuts or a solar power kit can increase the installed price.
Video intercoms, vehicle exit loops and additional remotes are priced separately.
Gate posts and hinge supports should be coordinated before stone or brick columns are built.
A deposit is due when the custom gate is ordered. Financing is available on approved credit.
How it works
Our driveway gate installation process
- 1.Site visit and measurementWe measure the opening, check the slope and available room, locate power and discuss access-control options.
- 2.Written proposalYou receive the recommended gate type, equipment list, estimated schedule and final installed price.
- 3.Posts and powerWe install the required posts, concrete, conduit or solar equipment and prepare the operator location.
- 4.Gate installationWe hang or set the gate, install the operator and safety devices, then adjust the alignment and travel limits.
- 5.Programming and handoffWe program the remotes, keypad and app, test the safety system and show you how to operate the manual release.
Gate repair, any brand
Driveway gate repair by symptom
We service many common gate-operator brands. The $89 diagnostic fee is waived when you approve the repair.
The gate is completely unresponsive
UsuallyA weak battery, power problem, damaged control board or solar charging issue.
Test power, battery and controls$185 to $485
The motor runs but the gate does not move
UsuallyA binding hinge, blocked track, damaged chain or worn operator gear.
Free the gate and repair the drive system$149 to $390
The gate starts, then stops or reverses
UsuallyA dirty or misaligned safety sensor, an obstruction or incorrect travel settings.
Inspect sensors and reset travel$89 to $220
The remote works but the keypad does not
UsuallyA weak keypad battery, weather damage or lost programming.
Reprogram or replace the keypad$89 to $260
The gate drags or will not latch
UsuallyA leaning post, worn hinge or gate panel that is out of alignment.
Realign the gate or repair the post$220 to $640
The gate opens by itself or will not stay closed
UsuallyA problem with the exit sensor, remote, receiver or control board.
Test the controls and repair the fault$129 to $320
Stuck closed with a car inside? Keep clear of the gate and do not force it. Call us and tell us access is blocked so we can prioritize the visit.
(864) 973-0180Gates around Seneca
What to consider before installing a driveway gate
Slope changes the gate type
A swing gate needs a clear, level arc. Sloped or tight entrances often work better with a track or cantilever slide gate.
Posts need a stable foundation
Gate posts carry more weight and movement than standard fence posts. Proper concrete footings help keep the gate aligned.
Power and surge protection matter
Long driveways may need trenching or solar power. Surge protection and grounding help protect the operator during storms.
Plan emergency access early
Some properties need fire-department, HOA or shared-access provisions. We identify these requirements before the gate is ordered.
Recent work
Recent driveway gate installs and repairs
Custom slide gate · Lake KeoweeModern wood and aluminum gate for a paved entrance
Built a wood-slat panel on a welded aluminum frame, installed the track and operator, and programmed the access controls.
- Custom-built panel
- App and keypad access
- $8,900 installed
Cantilever gate · SalemSolar cantilever gate for a sloped gravel driveway
Installed a cantilever system with no track across the gravel, plus solar power and keypad access.
- 20 ft opening
- Solar powered
- $9,750 installed
Gate automation · Fair PlayExisting farm gate upgraded with automatic access
Reused the existing tube-steel gate and added a swing operator, safety devices, solar power and a keypad.
- Existing gate reused
- Completed in one day
- $2,650 installed
Driveway gate FAQ
Frequently Asked Questions
How much does an automatic driveway gate cost?
Automating an existing gate typically costs $1,850 to $3,400. A new aluminum swing gate usually runs $4,800 to $8,900, while slide and cantilever systems range from $6,500 to $12,500. Width, material, power and site work affect the final price.
Do you build custom driveway gates?
Yes. We build swing, slide and cantilever gates to fit the opening. Available materials include aluminum, steel, wrought iron and wood on a welded frame, with simple, modern, privacy and ornamental styles.
Do you only install one gate or operator brand?
No. We build custom gate panels and work with several major operator and access-control brands. We recommend equipment based on the gate size, weight, power source and daily use.
Is a swing or slide gate better?
A swing gate works well on a level entrance with enough room for the panels to open. A slide or cantilever gate is often better for a sloped, tight or wide entrance.
Can you automate the gate I already have?
Often, yes. The gate must move freely and the posts must be stable. We inspect the gate first and explain any hinge, post or alignment work needed before adding an operator.
Can a driveway gate run on solar power?
Solar can work well for a residential gate when the entrance is far from electrical service and the panel has a clear location. Gate weight, daily use and shade determine the required system.
What happens when the power goes out?
The systems we install include battery backup and a manual release. We show you how to use the release safely during the installation handoff.
How do deliveries, guests and emergency services get in?
Options include keypad codes, remotes, app controls, video intercoms and vehicle exit sensors. Emergency-access requirements vary, so we confirm them with the property owner, HOA or local authority before installation.
Do I need a permit or HOA approval?
Requirements depend on the property, electrical work, road setback and community rules. We identify the likely approvals during the site visit and can provide gate drawings and equipment details for review.
What maintenance does an automatic gate need?
Annual service typically includes lubrication, alignment, battery testing, safety-sensor checks and operator adjustments. Track gates also need the ground track kept clear.
Will you repair a gate someone else installed?
Yes. We service many common operator and access-control brands. If an older operator no longer has replacement parts, we can quote a new operator while keeping the existing gate when possible.
How long does installation take?
Automating an existing gate may take one day. A new custom gate usually takes two to three weeks from the site visit to installation, depending on material and fabrication time.
Gate coverage
Driveway gate service in Seneca and nearby areas
Gate repair is usually same-day. New installs are scheduled after a free site visit.
- Seneca
- Clemson
- Walhalla
- Westminster
- Lake Keowee
- Pendleton
- Anderson
- Easley
- Pickens
- Fair Play
- Six Mile
- Salem
We also cover Salem, West Union, Fair Play, Townville, Mountain Rest, Six Mile and Central, plus the Lake Keowee and Lake Hartwell shorelines.
Free garage door estimate
Request a free estimate
Tell us what you need and we will call with pricing, usually within one business hour. Call for urgent repairs.
Call or text(864) 973-0180- Mon–Sat 7am–7pm · 24/7 emergency line
- Licensed & insured · SC Lic. #RBS-40217
- BBB A+ accredited · 4.9★ on Google
Request received
We will call within one business hour. For urgent repairs, call (864) 973-0180.